MAX4680CPE
| Parameters | |
|---|---|
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 55pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 300ns |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4680 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
MAX4680CPE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 1:1. Temperatures around 0°C~70°C TA are extended for operation. The total number of terminations is 16. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SPST - NC switching circuits. The circuits in this analogue multiplexer number 2. Try searching with MAX4680 to find analog multiplexer variants. An switch multiplexer with 1.25Ohm internal resistance has a value of 1.25Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The lowest voltage fed to the electronic component should be 4.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages range from 18V.
MAX4680CPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4680CPE Applications
There are a lot of Maxim Integrated MAX4680CPE Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Fault Tolerant Systems
- Video switching
- Microprocessor controlled systems
- Audio and video signal routing
- Isolation
- Microprocessor Controlled Analog Systems
- T1/E1 Terminals
- PBX interfaces
- Cable PC
