Parameters |
Factory Lead Time |
1 Week |
Contact Plating |
Lead, Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2001 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
500mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
444mW |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4684 |
Pin Count |
10 |
Power Supplies |
3V |
Number of Channels |
2 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
40μA |
Nominal Supply Current |
40pA |
Max Supply Current |
200nA |
Turn On Delay Time |
60 ns |
Supply Type |
Single |
Turn-Off Delay Time |
40 ns |
On-State Resistance (Max) |
800mOhm |
High Level Output Current |
300mA |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
64 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
84pF 37pF |
On-state Resistance Match-Nom |
0.06Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
50ns, 30ns |
Charge Injection |
200pC |
Channel-to-Channel Matching (ΔRon) |
60m Ω |
Crosstalk |
-68dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX4684EUB+T Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. 10 terminations have been made so far. This electronic part offers high-quality output due to its 2 channels. With a 3V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 10 pins. A SPDT switching circuit is used for these analog switches. A 2 circuit is present in this switch device. Try searching with MAX4684 if you're looking for variants. It has an internal resistance of 500mOhm. To find out what the functions of 10 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.8V. For this digital switch to work, 40μA current would suffice. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. Put voltage above 200nA on the multiplexer to cause damage.
MAX4684EUB+T Features
2 Channels
Switch Circuit: SPDT
40μA Supply Current
MAX4684EUB+T Applications
There are a lot of Maxim Integrated MAX4684EUB+T Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Intelligent PBX
- Multi-Line E1 Interface Cards
- USB 1.1 signal switching circuits
- DVD-R
- Modems
- MP3 players
- Optical Applications
- Fiber In The Loop (FITL)
- Medical