MAX4685EUB+

50ns, 30ns SPDT 800mOhm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4685 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4685EUB+
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 805
Description: 50ns, 30ns SPDT 800mOhm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4685 10 Pins 1nA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	800mOhm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	444mW
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4685
Output	SEPARATE OUTPUT
Pin Count	10
Power Supplies	3V
Number of Channels	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Nominal Supply Current	40pA
Max Supply Current	200nA
Turn On Delay Time	60 ns
Supply Type	Single
Turn-Off Delay Time	40 ns
On-State Resistance (Max)	800mOhm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	64 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	84pF 37pF
On-state Resistance Match-Nom	0.06Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	50ns, 30ns
Charge Injection	200pC
Channel-to-Channel Matching (ΔRon)	60m Ω
Crosstalk	-68dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	50ns
Switch-off Time-Max	30ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Height	950μm
Length	3.05mm
Width	3.05mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

MAX4685EUB+ Overview

Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. In total, there have been 10 terminations. A electrical component with 2 channels is capable of high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. It is injected into the electrical part body with 10 pins. A SPDT switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with MAX4685. The internal resistance of this digital multiplexer is 800mOhm. The datasheets for the 10 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. The digital multiplexer has a low cost Single supply. There should be 1.8V voltage fed to the electrical part below 1.8V. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 200nA on the digital multiplexer, damage may occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.