MAX4690CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4690 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 550pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 300ns |
| Normal Position | NC |
| Length | 19.175mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX4690CPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. The circuits in this analogue multiplexer number 2. Try searching with MAX4690 if you're looking for variants. It has an internal resistance of 1.25Ohm. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. When the digital multiplexer is charged above 500nA, damage can occur. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. A voltage of 20V can be used to operate the electronic component.
MAX4690CPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4690CPE Applications
There are a lot of Maxim Integrated MAX4690CPE Analog Switches & Multiplexers ICs applications.
- Imaging
- Precision test equipment
- Access Concentrators
- Precision instrumentation
- Communication systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Battery-powered systems
- Digital cross connects (DSX-1)
- High speed data transmission line cards
- Audio and video switching
