MAX4690CWE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4690 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 550pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 300ns |
| Normal Position | NC |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4690CWE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.295, 7.50mm Width). High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. SPST - NO switching circuits are used in these analog switch ics. This multiplexer is composed of 2 circuits. Search with MAX4690 if you are looking for analog multiplexer variants. A 1.25Ohm internal resistance characterizes this multiplexer. The analogue multiplexer in this example is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 4.5V. The analogue multiplexer may be damaged if voltage is greater than 500nA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. 20V operating voltages can be used with this electrical part.
MAX4690CWE Features
1 Channels
Switch Circuit: SPST - NO
MAX4690CWE Applications
There are a lot of Maxim Integrated MAX4690CWE Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Digital cross connects (DSX-1)
- Automotive applications
- CSU
- Medical
- Data Acquisition Systems
- DSUs
- Industrial
- FTTH
- Communication systems
