MAX4690EWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4690 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 550pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switch-off Time-Max | 175ns |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX4690EWE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.295, 7.50mm Width). To ensure high reliability, a new packaging method Tube is used. Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. Into the electrical component body are injected 16 pins. Unlike digital switches, these are based on SPST - NO switching circuits. 2 circuits are used in this analogue multiplexer. Try searching for MAX4690 variants of the analog switch ic. The internal resistance of this digital multiplexer is 1.25Ohm. Please refer to the datasheets for 16 pins functions. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 500nA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. This electrical part is compatible with 20V operating voltages.
MAX4690EWE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4690EWE+ Applications
There are a lot of Maxim Integrated MAX4690EWE+ Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- PDH Multiplexers
- Cell phones
- Audio/video switches
- Signal routing between systems
- Switching Systems
- Battery Powered Systems
- Remote wireless modules
- Data Acquisition Systems
- MP3 players
