MAX4691EGE-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Max Power Dissipation | 1.481W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4691 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 100nA |
| Throw Configuration | SP8T |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2V~5.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 68pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 100ns |
| Charge Injection | 0.1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 80ns |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 0.9mm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4691EGE-T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-VQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 8:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. In total, there are 16 terminations. By its 8 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. There are 16 pins injected into the electronic part body. It consists of 1 circuits. Using the MAX4691 search parameter, you can discover variants of the switch. This digital multiplexer has 70Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 11V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 2V. 100nA current would be enough for this multiplexer to operate. Despite this switch device's dual supply capability, its voltage should not exceed 5.5V. With dual power supplies, you should attach at least 2V. Operating voltages range from 9V.
MAX4691EGE-T Features
8 Channels
100nA Supply Current
MAX4691EGE-T Applications
There are a lot of Maxim Integrated MAX4691EGE-T Analog Switches & Multiplexers ICs applications.
- Avionics
- HDTV
- Cable PC
- Intelligent PBX
- Routers
- Multiplexers
- ISDN NT1/TA
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- MP3 players
- Communication systems
