MAX4691ETE+
| Parameters | |
|---|---|
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 68pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 100ns |
| Charge Injection | 0.1pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.349W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4691 |
| Pin Count | 16 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1μA |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 2V |
MAX4691ETE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WQFN Exposed Pad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 8:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 8 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the electrical part body. Circuits number 1 make up this analogue multiplexer. Try searching with MAX4691 if you're looking for variants. This digital multiplexer has 70Ohm internal resistance. The functions of 16 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 11V should not normally be supplied to the switches. 2V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. When using dual power supplies, you should attach at least 2V. It is integrated with a SINGLE-ENDED MULTIPLEXER analog IC.
MAX4691ETE+ Features
8 Channels
1μA Supply Current
MAX4691ETE+ Applications
There are a lot of Maxim Integrated MAX4691ETE+ Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- E1 Network Equipment
- DVD-R
- Modems
- DSLAMs
- Microprocessor controlled systems
- Relay replacements
- Voice over IP/DSL – Integrated Access Devices, Smart
- Avionics test equipment
- Mechanical reed relay replacement
