MAX4695EGC+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-VFQFN Exposed Pad |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 330mW |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4695 |
| Pin Count | 12 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 18 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 18ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -82dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4695EGC+T Overview
This electronic part is conveniently packaged in 12-VFQFN Exposed Pad, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 12. High-quality output is provided by the electronic component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. There are 12 pins injected into the electronic part body. These analog multiplexers are built based on SPDT switching circuits. A total of 2 circuits make up this switch device. Search with MAX4695 if you are looking for analog multiplexer variants. It has an internal resistance of 60Ohm. For functions related to 12 pins, please refer to the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.8V. An operating current of 1μA would be sufficient for this switch device. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Operating voltages range from 5V.
MAX4695EGC+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4695EGC+T Applications
There are a lot of Maxim Integrated MAX4695EGC+T Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Mechanical reed relay replacement
- SONET
- ATM
- Industrial
- Power routing
- Microprocessor controlled systems
- Precision test equipment
- Cellular phones
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
