MAX4695ETC+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFQFN Exposed Pad |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 330mW |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4695 |
| Pin Count | 12 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 18 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 7pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 18ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -82dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4695ETC+T Overview
Shipping overseas is convenient with the electronic component packed in 12-WFQFN Exposed Pad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 12. The electronic part provides high-quality output because it has 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. 12 pins are injected to the electronic part body. A SPDT switching circuit is used to build these analog multiplexers. There are 2 circuits in this multiplexer. Using the MAX4695 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 60Ohm. The datasheets for the 12 pins explain the functions. Users should never supply a voltage higher than 5.5V to a switch device. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.8V. It would be sufficient to run this analogue multiplexer with 1μA current. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. A voltage higher than 1μA may cause damage to the switch multiplexer. A voltage of 5V can be used to operate the electronic component.
MAX4695ETC+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4695ETC+T Applications
There are a lot of Maxim Integrated MAX4695ETC+T Analog Switches & Multiplexers ICs applications.
- Communications systems
- Switching Systems
- Video signal routing
- Routers
- High-Voltage
- Precision instrumentation
- Automotive applications
- High speed data transmission line cards
- Medical
- Multiplexers
