MAX4700CAE
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4700 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 550pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 300ns |
| Height Seated (Max) | 1.99mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
MAX4700CAE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SSOP (0.209, 5.30mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 2 channels. An 15V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NO/NC switching circuit is used to build these analog multiplexers. Try searching for MAX4700 variants of the analog switch ic. A 1.25Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 4.5V. The analogue multiplexer may be damaged if voltage is greater than 500nA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 20V operating voltages are supported by the electronic component.
MAX4700CAE Features
2 Channels
Switch Circuit: SPST - NO/NC
MAX4700CAE Applications
There are a lot of Maxim Integrated MAX4700CAE Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Ultrasound
- Mechanical reed relay replacement
- New designs requiring multiplexer functions
- Channel Banks
- USB 1.1 signal switching circuits
- Cellular phones
- Relay replacements
- Avionics and Military Systems
- Access Concentrators
