MAX4700CWE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4700 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.09Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 275ns, 175ns |
| Charge Injection | 550pC |
| Channel-to-Channel Matching (ΔRon) | 90m Ω |
| Crosstalk | -65dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4700CWE Overview
The electrical component comes in 16-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around 0°C~70°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. The analog switch ics are built using SPST - NO/NC switching circuits. A total of 2 circuits make up this switch device. Try searching with MAX4700 to find analog multiplexer variants. An switch multiplexer with 1.25Ohm internal resistance has a value of 1.25Ohm. The datasheets for the 16 pins explain the functions. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. It is recommended that the electrical component receives a voltage of 4.5V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4700CWE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4700CWE Applications
There are a lot of Maxim Integrated MAX4700CWE Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Communication systems
- T1/E1 Terminals
- Precision instrumentation
- Relay replacements
- ISDN NT1/TA
- Remote Powered Equipment
- Video switching
- Audio and video routing
- Voice over IP/DSL – Integrated Access Devices, Smart
