MAX4701ETE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 444mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4701 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Turn On Delay Time | 20 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 35 ns |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 75Ohm |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 35ns, 20ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -79dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 45ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4701ETE+T Overview
Packed in 16-WFQFN Exposed Pad, the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 2 channels is capable of high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. 16 pins are injected to the electronic part body. These analog multiplexers are built based on DPDT switching circuits. It consists of 2 circuits. Try searching with MAX4701 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 75Ohm. Please refer to the datasheets for 16 pins functions. It is a typical Multiplexer or Switches analog multiplexer. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.8V. 1μA current would be enough for this multiplexer to operate. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source.
MAX4701ETE+T Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
-3db Bandwidth: 250MHz
MAX4701ETE+T Applications
There are a lot of Maxim Integrated MAX4701ETE+T Analog Switches & Multiplexers ICs applications.
- PBXs
- Industrial control systems
- Microprocessor Controlled Analog Systems
- PBX interfaces
- Microwave transmission systems
- SONET
- Automotive applications
- New designs requiring multiplexer functions
- Fiber to the Home
- Medical
