MAX4701EUE+T

35ns, 20ns DPDT 75Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4701 16 Pins 500pA 3V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4701EUE+T
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 390
Description: 35ns, 20ns DPDT 75Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4701 16 Pins 500pA 3V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	75Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	444mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4701
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	5V
Number of Channels	2
Number of Circuits	2
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	20 ns
Supply Type	Single
Turn-Off Delay Time	35 ns
-3db Bandwidth	250MHz
On-State Resistance (Max)	75Ohm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	76 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	8pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	35ns, 20ns
Charge Injection	0.5pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-79dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount

MAX4701EUE+T Overview

The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:2. Operating temperature extended to -40°C~85°C TA. 16 terminations have been made so far. By its 2 channels, the electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Multiplexers built on a DPDT switching circuit are built. The multiplexer consists of 2 circuits. Try searching with MAX4701 if you're looking for variants. The internal resistance of this digital multiplexer is 75Ohm. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. For this multiplexer to operate, 1μA current would be sufficient. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The electrical part can be operated at 5V voltage levels.