Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
16-WFQFN Exposed Pad |
Surface Mount |
YES |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4702 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
S-XQCC-N16 |
Qualification Status |
Not Qualified |
Supply Voltage-Max (Vsup) |
5.5V |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
4 |
-3db Bandwidth |
250MHz |
On-State Resistance (Max) |
75Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
76 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
8pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
35ns, 20ns |
Charge Injection |
0.5pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-79dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
35ns |
Switch-off Time-Max |
20ns |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
0.8mm |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
MAX4702ETE+T Overview
Due to its 16-WFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SPDT switching circuit is used for these analog switches. A total of 4 circuits make up this switch device. Try searching for the analog switch ic with MAX4702 if you are looking for variants. There is a standard Multiplexer or Switches analogue multiplexer here. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4702ETE+T Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 250MHz
MAX4702ETE+T Applications
There are a lot of Maxim Integrated MAX4702ETE+T Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Battery-powered systems
- Remote wireless modules
- Precision test equipment
- High reliability control systems
- Access Concentrators
- Cross Connects
- Industrial
- Cable Modem
- Low-Voltage