banner_page

MAX4704EGC+T

60ns, 20ns SP4T 60Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4704 12 Pins 100pA 3V 12-VFQFN Exposed Pad


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4704EGC+T
  • Package: 12-VFQFN Exposed Pad
  • Datasheet: PDF
  • Stock: 363
  • Description: 60ns, 20ns SP4T 60Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4704 12 Pins 100pA 3V 12-VFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 12-VFQFN Exposed Pad
Number of Pins 12
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 12
ECCN Code EAR99
Resistance 60Ohm
Terminal Finish Matte Tin (Sn)
Max Power Dissipation 952mW
Technology CMOS
Terminal Position QUAD
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3V
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number MAX4704
Pin Count 12
Operating Supply Voltage 5V
Number of Channels 4
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 1μA
Propagation Delay 60 ns
Turn On Delay Time 60 ns
Logic Function Multiplexer
Supply Type Single
Bandwidth 200MHz
Turn-Off Delay Time 20 ns
On-State Resistance (Max) 60Ohm
Multiplexer/Demultiplexer Circuit 4:1
Off-state Isolation-Nom 85 dB
Current - Leakage (IS(off)) (Max) 100pA
Channel Capacitance (CS(off), CD(off)) 7pF
On-state Resistance Match-Nom 1Ohm
Switch Circuit SP4T
Switch Time (Ton, Toff) (Max) 60ns, 20ns
Charge Injection 2pC
Channel-to-Channel Matching (ΔRon) 1 Ω
Crosstalk -90dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.8V~5.5V
Length 3mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

MAX4704EGC+T Overview


Packed in 12-VFQFN Exposed Pad, the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 4:1. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 12 terminations. The electronic part provides high-quality output because it has 4 channels. With a 3V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 12 series. SP4T switching circuits are used in these analog switch ics. There are 1 circuits in this switch device. Try searching for the analog switch ic with MAX4704 if you are looking for variants. A 60Ohm internal resistance characterizes this multiplexer. The functions of 12 pins can be found in the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. A cost-effective Single supply type analogue multiplexer. 1.8V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1μA current. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. There is a voltage range of 5V operating voltages for the electrical part. There are 200MHz bandwidths for data transfer.

MAX4704EGC+T Features


4 Channels
Switch Circuit: SP4T
1μA Supply Current
Bandwidth: 200MHz

MAX4704EGC+T Applications


There are a lot of Maxim Integrated MAX4704EGC+T Analog Switches & Multiplexers ICs applications.

  • E1 Network Equipment
  • Medical systems
  • Microprocessor Controlled Analog Systems
  • Audio signal routing
  • Avionics test equipment
  • Cross Connects
  • Sample-and-hold systems
  • SDH/SONET multiplexers
  • RGB switches
  • Voice over IP/DSL – Integrated Access Devices, Smart

Write a review

Note: HTML is not translated!
    Bad           Good