MAX4708ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 400Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4708 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 525μA |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Current-Max (Isup) | 0.75mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 400Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 10pF 19pF |
| On-state Resistance Match-Nom | 15Ohm |
| Switch Time (Ton, Toff) (Max) | 275ns, 200ns |
| Channel-to-Channel Matching (ΔRon) | 15 Ω (Max) |
| Crosstalk | -62dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 275ns |
| Switch-off Time-Max | 200ns |
| Signal Current-Max | 0.03A |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4708ESE+T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 8 channels. A 15V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. This multiplexer is composed of 1 circuits. Try searching with MAX4708 if you're looking for variants. A 400Ohm internal resistance characterizes this multiplexer. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 36V should not normally be supplied to the switches. 9V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 525μA current. Despite this switch device's dual supply capability, its voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. This product is integrated with an analog integrated circuit (IC) of type SINGLE-ENDED MULTIPLEXER. The electrical part can be operated at 28V voltage levels.
MAX4708ESE+T Features
8 Channels
525μA Supply Current
MAX4708ESE+T Applications
There are a lot of Maxim Integrated MAX4708ESE+T Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Video signal routing
- Public switching systems
- High speed data transmission line cards
- Battery-powered systems
- Battery Powered Instruments
- PDAs
- Communications systems
- Audio and video signal routing
- Ultrasound
