MAX4712CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4712 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2.7V |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 59 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 125ns, 80ns |
| Charge Injection | 25pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -87dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 80ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4712CPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around 0°C~70°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. There are 16 pins injected into the electronic part body. Unlike digital switches, these are based on SPST - NO switching circuits. 4 circuits are used in this analogue multiplexer. Use MAX4712 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 25Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 11V to a switch device. 2.7V is the lowest voltage that should be fed to the electronic electronic part. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. When using dual power supplies, you should attach at least 2.7V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Additional features of the electronic component include: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V.
MAX4712CPE Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V
MAX4712CPE Applications
There are a lot of Maxim Integrated MAX4712CPE Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- 65 V DACs
- SONET
- Intelligent PBX
- Automotive applications
- Residential Gateways, Home Gateway/Router
- Industrial control systems
- PBXs
- Sample-and-hold systems
- PDH Multiplexers
