MAX4712CUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 25Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V |
| Max Power Dissipation | 457mW |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4712 |
| Pin Count | 16 |
| Operating Supply Voltage | 5.5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 75μA |
| Max Supply Current | 65μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2.7V~5.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 500 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 59 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 125ns, 80ns |
| Charge Injection | 25pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -87dB @ 1MHz |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 80ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4712CUE+T Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around 0°C~70°C TA. 16 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. Multiplexers built on a SPST - NO switching circuit are built. 4 circuits are used in this analogue multiplexer. Using the MAX4712 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 25Ohm. The datasheets for the 16 pins explain the functions. Users should never supply a voltage higher than 11V to a switch device. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 2.7V as the lowest voltage for the electrical part. A digital multiplexer may suffer damage if voltage is applied above 65μA. There is no problem with using dual supply voltage, but it should not exceed 5.5V. In the case of dual power supplies, you should connect at least 2.7V. Operating voltages range from 5.5V. Don't miss this electronic component's additional features, such as: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V.
MAX4712CUE+T Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V
MAX4712CUE+T Applications
There are a lot of Maxim Integrated MAX4712CUE+T Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- PDH Multiplexers
- Precision test equipment
- Switching Systems
- High reliability control systems
- PDAs
- Precision data acquisition
- Remote Powered Equipment
- Imaging
- PBX interfaces
