MAX4713CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4713 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 59 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 125ns, 80ns |
| Charge Injection | 25pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -87dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 80ns |
| Length | 19.175mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX4713CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Through Hole position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. A 5V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. A SPST - NO/NC switching circuit is used for these analog switches. There are 4 circuits in this multiplexer. Using the MAX4713 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 25Ohm. The analogue multiplexer in this example is a typical Multiplexer or Switches. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. This electronic part has additional features, such as: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V.
MAX4713CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
Additional Features: CAN ALSO OPERATE FROM SINGLE SUPPLY OF 2.7V TO 11V
MAX4713CPE Applications
There are a lot of Maxim Integrated MAX4713CPE Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- Multi-Line E1 Interface Cards
- High-Voltage
- Low-Voltage
- Public switching systems
- Video signal routing
- Central office
- CSU
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Existing multiplexer applications (both fault-protected and nonfault-protected)
