MAX4713EUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 25Ohm |
| Max Power Dissipation | 457mW |
| Base Part Number | MAX4713 |
| Operating Supply Voltage | 5V |
| Number of Circuits | 4 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 34μA |
| Max Supply Current | 65μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 500 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~11V ±2.7V~5.5V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 175 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 125ns, 80ns |
| Charge Injection | 25pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -87dB @ 1MHz |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4713EUE+T Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. SPST - NO/NC switching circuits are used in these analog switch ics. A total of 4 circuits make up this switch device. Try searching with MAX4713 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 25Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users shouldn't supply more than 11V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage the electronic part should receive is 2.7V. Put voltage above 65μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. The voltage should be at least 2.7V if you are using dual power supplies. 5V operating voltages are supported by the electronic component.
MAX4713EUE+T Features
Switch Circuit: SPST - NO/NC
MAX4713EUE+T Applications
There are a lot of Maxim Integrated MAX4713EUE+T Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- ATM
- Private Branch Exchange (PBX)
- Precision instrumentation
- Medical
- High reliability control systems
- Intelligent PBX
- Modems
- Precision data acquisition
- Medical Instrumentation
