MAX4714ELT+T
| Parameters | |
|---|---|
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-WFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 800mOhm |
| Terminal Finish | GOLD |
| Max Power Dissipation | 247mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4714 |
| Pin Count | 6 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 40nA |
| Nominal Supply Current | 2μA |
| Max Supply Current | 200nA |
| Turn On Delay Time | 15 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 18ns, 12ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -54dB @ 1MHz |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Height Seated (Max) | 0.8mm |
| Radiation Hardening | No |
MAX4714ELT+T Overview
The electronic component is convenient to ship overseas because it is packed in a 6-WFDFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there are 6 terminations. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 1.8V voltage supply. Electronic part bodies are injected with 6 pins. Circuits based on SPDT switching are used to construct these analog switch ics. A total of 1 circuits make up this switch device. MAX4714 can be used to search for analog multiplexer variants. It has an internal resistance of 800mOhm. For details about the functions of 6 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 3.6V. The analog switch ic is of the Single supply type and is cost-effective. There should be 1.6V voltage fed to the electrical part below 1.6V. For this multiplexer to operate, 40nA current would be sufficient. Draining from a single voltage supply, this analog switch requires a voltage of 1.6V~3.6V. A digital multiplexer may suffer damage if voltage is applied above 200nA. There is a voltage range of 3V operating voltages for the electrical part.
MAX4714ELT+T Features
1 Channels
Switch Circuit: SPDT
40nA Supply Current
MAX4714ELT+T Applications
There are a lot of Maxim Integrated MAX4714ELT+T Analog Switches & Multiplexers ICs applications.
- Cellular phones
- Mechanical reed relay replacement
- Ultrasound
- Industrial control systems
- E1 Multiplexer
- High speed data transmission line cards
- Fault Tolerant Systems
- Communication systems
- Data Acquisition Systems
- ISDN NT1/TA
