MAX4714EXT+T
| Parameters | |
|---|---|
| Turn On Delay Time | 18 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| On-State Resistance (Max) | 800mOhm |
| High Level Output Current | 150mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 18ns, 12ns |
| Charge Injection | 22pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -54dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 25ns |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28.009329mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 800mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 247mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4714 |
| Pin Count | 6 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 40nA |
| Max Supply Current | 200nA |
MAX4714EXT+T Overview
Shipping overseas is convenient due to the electrical component's packing in 6-TSSOP, SC-88, SOT-363. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 6. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 1.8V, it should be turned on and run. The electrical component body receives 6 pins. A SPDT switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 1. Use MAX4714 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 800mOhm. To find out what the functions of 6 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.6V. This digital switch can be operated with a current of 40nA. Using only a single voltage supply, this analog switch requires 1.6V~3.6V voltage. It may damage the digital multiplexer if the voltage is higher than 200nA.
MAX4714EXT+T Features
1 Channels
Switch Circuit: SPDT
40nA Supply Current
MAX4714EXT+T Applications
There are a lot of Maxim Integrated MAX4714EXT+T Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Central office
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Cable PC
- Medical
- Relay replacements
- Sample-and-hold systems
- SDH/SONET multiplexers
- Avionics test equipment
- Industrial
