MAX4715EXK-T
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 19.986414mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 400mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 247mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4715 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 40nA |
| Max Supply Current | 200nA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 18 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| On-State Resistance (Max) | 400mOhm |
| High Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 54 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 18ns, 12ns |
| Charge Injection | 20pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NO |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4715EXK-T Overview
Packed in 5-TSSOP, SC-70-5, SOT-353, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 5 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. With a 3V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 5 series. These analog multiplexers are built based on SPST - NO switching circuits. There are 1 circuits in this multiplexer. Using the MAX4715 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 400mOhm. You can find the functions of the 5 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 1.6V. 40nA current would be enough for this multiplexer to operate. Using a single voltage supply, this switch device consumes 1.6V~3.6V volts. If put voltage greater than 200nA on the device, damage may be caused to the analogue multiplexer. Its conductivity is 4-bit.
MAX4715EXK-T Features
1 Channels
Switch Circuit: SPST - NO
40nA Supply Current
4-Bit
MAX4715EXK-T Applications
There are a lot of Maxim Integrated MAX4715EXK-T Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- DSLAMs
- Microprocessor controlled systems
- Audio/video switches
- New designs requiring multiplexer functions
- SDH
- PDAs
- Isolation
- Audio and video signal routing
- Video switching
