MAX4717EBC+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFBGA, WLCSP |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 444mW |
| Technology | BICMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4717 |
| Output | SEPARATE OUTPUT |
| Pin Count | 12 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 80 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 80ns, 40ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.67mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4717EBC+T Overview
This electronic part is conveniently packaged in 12-WFBGA, WLCSP, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. A total of 12 terminations have been recorded. As a result of its 1 channels, this electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. This electronic part can be found in the 12 series. SPDT switching circuits are used in these analog switch ics. There are 2 circuits in this switch device. Try searching for the analog switch ic with MAX4717 if you are looking for variants. A 4.5Ohm internal resistance characterizes this multiplexer. For details about the functions of 12 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Digital switch that provides Single power at a cost-effective price. There should be 1.8V voltage fed to the electrical part below 1.8V. This multiplexer would work with 1μA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. It may damage the digital multiplexer if the voltage is higher than 1μA. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4717EBC+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4717EBC+T Applications
There are a lot of Maxim Integrated MAX4717EBC+T Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- PDH Multiplexers
- Cellular phones
- Sample hold systems
- Data switching
- Communication systems
- Medical Instrumentation
- FTTH
- Cross Connects
- Relay Replacement
