Parameters |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
80 ns |
Supply Type |
Single |
Bandwidth |
300MHz |
Turn-Off Delay Time |
40 ns |
On-State Resistance (Max) |
4.5Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
9pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
80ns, 40ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-110dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height |
950μm |
Length |
3.05mm |
Width |
3.05mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
4.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
444mW |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4717 |
MAX4717EUB+ Overview
Presented in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 10. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Into the electrical component body are injected 10 pins. Unlike digital switches, these are based on SPDT switching circuits. There are 2 circuits in this switch device. MAX4717 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 4.5Ohm. To find out what the functions of 10 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analog switch ics with Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.8V. 1μA current would be enough for this multiplexer to operate. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. It is possible to transfer data over a 300MHz-bandwidth.
MAX4717EUB+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 300MHz
MAX4717EUB+ Applications
There are a lot of Maxim Integrated MAX4717EUB+ Analog Switches & Multiplexers ICs applications.
- Automotive applications
- MP3 players
- Digital Cross-Connects
- Data Acquisition Systems
- High-Voltage
- SDH/SONET multiplexers
- Precision data acquisition
- PBXs
- Signal routing between systems
- Digital access cross connects