MAX4719EUB+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 444mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4719 |
| Pin Count | 10 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 80ns, 40ns |
| Charge Injection | 18pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 40ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4719EUB+T Overview
The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. Total terminations are 10. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. Into the electrical component body are injected 10 pins. These analog multiplexers are built based on SPDT switching circuits. A total of 2 circuits make up this switch device. Try searching with MAX4719 if you're looking for variants. This digital multiplexer has 20Ohm internal resistance. To find out what the 10 pins do, please refer to the datasheets. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.8V should be applied to the electronic component. An operating current of 1μA would be sufficient for this switch device. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The electronic component can function from 5V.
MAX4719EUB+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4719EUB+T Applications
There are a lot of Maxim Integrated MAX4719EUB+T Analog Switches & Multiplexers ICs applications.
- Medical systems
- Communication systems
- Mechanical reed relay replacement
- Channel Banks
- Access Concentrators
- Cellular phones
- PDAs
- Fiber In The Loop (FITL)
- New designs requiring multiplexer functions
- Audio and video switching
