MAX4723EUA+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 4.5Ohm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 362mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4723 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 80 ns |
| Data Rate | 12 Mbps |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 4.5Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 40ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4723EUA+T Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. In total, there have been 8 terminations. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. Into the electrical component body are injected 8 pins. These analog multiplexers are built based on SPST - NO/NC switching circuits. This multiplexer is composed of 2 circuits. Try searching for MAX4723 variants of the analog switch ic. As far as internal resistance is concerned, it has 4.5Ohm. To find out what the 8 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. A low voltage of 1.8V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. When the digital multiplexer is charged above 1μA, damage can occur. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating voltages range from 5V.
MAX4723EUA+T Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4723EUA+T Applications
There are a lot of Maxim Integrated MAX4723EUA+T Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- PCMCIA cards
- Battery Powered Instruments
- Avionics test equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics and Military Systems
- HDTV
- Sample-and-hold systems
- Industrial
- RGB switches
