banner_page

MAX4729EXT+T

45ns, 26ns SPDT 5.5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4729 6 Pins 2nA 2.7V 6-TSSOP, SC-88, SOT-363


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4729EXT+T
  • Package: 6-TSSOP, SC-88, SOT-363
  • Datasheet: PDF
  • Stock: 775
  • Description: 45ns, 26ns SPDT 5.5Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4729 6 Pins 2nA 2.7V 6-TSSOP, SC-88, SOT-363(Kg)

Details

Tags

Parameters
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2005
JESD-609 Code e4
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
ECCN Code EAR99
Resistance 5.5Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 245mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 2.7V
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number MAX4729
Pin Count 6
Number of Channels 1
Voltage 5V
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 1nA
Max Supply Current 1μA
Turn On Delay Time 45 ns
Supply Type Single
Turn-Off Delay Time 26 ns
-3db Bandwidth 300MHz
On-State Resistance (Max) 5.5Ohm
High Level Output Current 80mA
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 45 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 6.5pF
On-state Resistance Match-Nom 0.05Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 45ns, 26ns
Charge Injection 3pC
Channel-to-Channel Matching (ΔRon) 50m Ω
Crosstalk -67dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.8V~5.5V
Height 1mm
Length 2.2mm
Width 1.35mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Factory Lead Time 1 Week
Contact Plating Gold
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 6-TSSOP, SC-88, SOT-363
Number of Pins 6
Weight 28.009329mg

MAX4729EXT+T Overview


Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. 6 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 2.7V is used, the electronic component should be turned on and run. An injection of 6 pins is performed into the body of the electrical component. The analog switch ics are built using SPDT switching circuits. The circuits in this analogue multiplexer number 1. If you are looking for variants of the digital switch, trying search with MAX4729. Analog switches have 5.5Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. It is recommended to use 1.8V as the lowest voltage for the electrical part. The switch device would be able to operate with 1nA current. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur.

MAX4729EXT+T Features


1 Channels
Switch Circuit: SPDT
1nA Supply Current
-3db Bandwidth: 300MHz

MAX4729EXT+T Applications


There are a lot of Maxim Integrated MAX4729EXT+T Analog Switches & Multiplexers ICs applications.

  • Isolation
  • Mechanical reed relay replacement
  • Sample-and-hold systems
  • Power routing
  • Microprocessor controlled systems
  • ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
  • Cable Telephony – NIU, Set-Top Box, Home Side Box
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • HDTV
  • Industrial and process control systems

Write a review

Note: HTML is not translated!
    Bad           Good