MAX4734ETC+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFQFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4734 |
| Pin Count | 12 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 3.6V |
| Number of Channels | 4 |
| Number of Circuits | 1 |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 33pF 117pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 60pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -56dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Switch-off Time-Max | 25ns |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
MAX4734ETC+ Overview
Due to its 12-WFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. 4:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 12. The electronic part provides high-quality output because it has 4 channels. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 12 series. Multiplexers built on a SP4T switching circuit are built. The circuits in this analogue multiplexer number 1. Try searching for the analog switch ic with MAX4734 if you are looking for variants. Please refer to the datasheets for 12 pins functions. Multiplexer or Switches is a typical switch device. A voltage of 1.6V~3.6V is required to drain this analog switch from a single voltage supply. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board.
MAX4734ETC+ Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 90MHz
MAX4734ETC+ Applications
There are a lot of Maxim Integrated MAX4734ETC+ Analog Switches & Multiplexers ICs applications.
- SONET
- Industrial control systems
- Routers
- Data Acquisition Systems
- Relay replacements
- Imaging
- Remote Powered Equipment
- Precision test equipment
- Switching Systems
- SDH
