MAX4736ETC+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-WFQFN Exposed Pad |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| Resistance | 800mOhm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 444mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4736 |
| Output | SEPARATE OUTPUT |
| Pin Count | 12 |
| Power Supplies | 1.8/3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| -3db Bandwidth | 130MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 33pF 60pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 60pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~4.2V |
| Height Seated (Max) | 0.9mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4736ETC+T Overview
Due to its 12-WFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. A total of 12 terminations have been recorded. A 1 channel electronic part produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. There is an electrical component included in the 12 series. These analog multiplexers are built based on SPDT switching circuits. There are 2 circuits in this multiplexer. If you are looking for variants of the digital switch, trying search with MAX4736. Internally, this switch multiplexer has a resistance of 800mOhm. To find out what the functions of 12 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 3.6V to a switch device. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.6V. In order to operate this switch device, it would need a current of 1μA. Using only a single voltage supply, this analog switch requires 1.6V~4.2V voltage. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4736ETC+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 130MHz
MAX4736ETC+T Applications
There are a lot of Maxim Integrated MAX4736ETC+T Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Sample-and-hold systems
- High-Voltage
- Digital access cross connects
- Multi-Line E1 Interface Cards
- Industrial control systems
- E1 Network Equipment
- Communication systems
- Avionics and Military Systems
- Mechanical reed relay replacement
