Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2012 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
800mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
444mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4736 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Operating Supply Voltage |
3V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.6V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
30 ns |
Supply Type |
Single |
Bandwidth |
130MHz |
Turn-Off Delay Time |
25 ns |
On-State Resistance (Max) |
800mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
52 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
33pF 60pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
25ns, 20ns |
Charge Injection |
60pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-78dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.6V~4.2V |
Drain to Source Resistance |
800mOhm |
Height |
950μm |
Length |
3.05mm |
Width |
3.05mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
MAX4736EUB+ Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. In Surface Mount, this analog switch is mounted. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. In total, 10 terminations have occurred. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. 10 pins are injected to the electronic part body. On the other hand, analog switches can be constructed using SPDT switching circuits. There are 2 circuits in this multiplexer. Try searching with MAX4736 if you're looking for variants. The internal resistance of this digital multiplexer is 800mOhm. The datasheets for the 10 pins explain the functions. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 3.6V to a switch device. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.6V. The analogue multiplexer could operate on 1μA current. A voltage of 1.6V~4.2V is required to drain this analog switch from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. There is a voltage range of 3V operating voltages for the electrical part. 130MHz-bandwidths can be used to transfer data between multiplexers. There is 800mOhm Drain to Source resistance on this electronic part.
MAX4736EUB+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Bandwidth: 130MHz
Drain-to-Source resistance: 800mOhm
MAX4736EUB+ Applications
There are a lot of Maxim Integrated MAX4736EUB+ Analog Switches & Multiplexers ICs applications.
- SONET
- PBX interfaces
- Cellular phones
- Cross Connects
- Avionics test equipment
- 65 V DACs
- Fault Tolerant Systems
- Isolation
- Central office
- USB 1.1 signal switching circuits