MAX4741ELA+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 800mOhm |
| Terminal Finish | GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4741 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Nominal Supply Current | 200nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 35 ns |
| -3db Bandwidth | 100MHz |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 32pF 32pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 24ns, 16ns |
| Charge Injection | 28pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 16ns |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NO |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4741ELA+T Overview
Presented in 8-WFDFN, this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. This electrical component is included in the 8 series of products. The analog switch ics are built using SPST - NO switching circuits. There are 2 circuits in this switch device. Try searching for the analog switch ic with MAX4741 if you are looking for variants. This digital multiplexer has 800mOhm internal resistance. For functions related to 8 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 3.6V to a switch device. Digital switch that provides Single power at a cost-effective price. The lowest voltage the electronic part should receive is 1.6V. Analogue multiplexers require a 1.6V~3.6V voltage to drain from a single voltage supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
MAX4741ELA+T Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 100MHz
MAX4741ELA+T Applications
There are a lot of Maxim Integrated MAX4741ELA+T Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Isolation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cable PC
- Precision data acquisition
- High reliability control systems
- Fiber to the Home
- Microwave transmission systems
- Low-Voltage
- Automatic test equipment
