MAX4747EUD+T
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4747 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 60 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 150 ns |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 85ns, 45ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -84dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~11V |
| Normal Position | NO |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
MAX4747EUD+T Overview
The electrical component comes in 14-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. A total of 14 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. A 3V voltage supply should turn on and run the electronic component. 14 pins are injected to the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. A 4 circuit is present in this switch device. Use MAX4747 to search for variants of the digital switches. In this multiplexer, the internal resistance is 50Ohm. For details about the functions of 14 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 11V in normal situations. The analog switch ic is of the Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2V. In order to operate this switch device, it would need a current of 1μA. Draining from a single voltage supply, this analog switch requires a voltage of 2V~11V. Putting voltage greater than 1μA on the multiplexer may cause damage. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4747EUD+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 250MHz
MAX4747EUD+T Applications
There are a lot of Maxim Integrated MAX4747EUD+T Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Frame Relay Equipment
- SDH
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communications systems
- Industrial
- Routers
- Public switching systems
- Medical Instrumentation
- Signal routing between systems
