MAX4750ETE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.349W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.8mm |
| Base Part Number | MAX4750 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 11V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 60 ns |
| -3db Bandwidth | 250MHz |
| On-State Resistance (Max) | 25Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 85ns, 45ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -84dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~11V |
| Height Seated (Max) | 0.8mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4750ETE+T Overview
The electrical component comes in 16-WQFN Exposed Pad packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. As part of its design, the 16 series is equipped with this electronic component. Unlike digital switches, these are based on SPDT switching circuits. There are 2 circuits in this switch device. Search with MAX4750 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 50Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 11V. Analog switch ics with Single supply type are cost-effective. There should be 2V voltage fed to the electrical part below 2V. For this digital switch to work, 1μA current would suffice. Using only a single voltage supply, this analog switch requires 2V~11V voltage. Putting voltage greater than 1μA on the multiplexer may cause damage. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 9V operating voltages are supported by the electronic component.
MAX4750ETE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 250MHz
MAX4750ETE+T Applications
There are a lot of Maxim Integrated MAX4750ETE+T Analog Switches & Multiplexers ICs applications.
- Power routing
- Avionics and Military Systems
- Relay Replacement
- Industrial
- Remote Powered Equipment
- E1 Multiplexer
- Communication systems
- Data switching
- MP3 players
- Microprocessor controlled systems
