MAX4752EGE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.349W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4752 |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 900mOhm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2.5nA |
| Channel Capacitance (CS(off), CD(off)) | 31pF 30pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 21pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4752EGE+T Overview
Packed in 16-VFQFN Exposed Pad, the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 4. If you are looking for variants of the digital switch, trying search with MAX4752. Internally, this switch multiplexer has a resistance of 900mOhm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 3.6V. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 1.6V should be applied to the electronic component. This digital switch can be operated with a current of 1μA. The voltage required by this switch device is 1.6V~3.6V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The electronic component can function from 3V.
MAX4752EGE+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4752EGE+T Applications
There are a lot of Maxim Integrated MAX4752EGE+T Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- High reliability control systems
- Sample-and-hold systems
- DSUs
- ISDN NT1/TA
- E1 Network Equipment
- Audio and video signal routing
- Cable Modem
- Medical Instrumentation
- Avionics
