MAX4752EUD+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4752 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 3V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 2.5nA |
| Channel Capacitance (CS(off), CD(off)) | 31pF 30pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 21pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4752EUD+T Overview
Shipping overseas is convenient due to the electrical component's packing in 14-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around -40°C~85°C TA. Totally, there are 14 terminations. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 1.8V, it should be turned on and run. Into the electrical component body are injected 14 pins. A SPST - NO switching circuit is used for these analog switches. There are 4 circuits in this multiplexer. Try searching for MAX4752 variants of the analog switch ic. This digital multiplexer has 900mOhm internal resistance. The datasheets for the 14 pins explain the functions. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 3.6V in normal situations. Digital switch that provides Single power at a cost-effective price. 1.6V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1μA current would suffice. Using a single voltage supply, this switch device consumes 1.6V~3.6V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. 3V operating voltages can be used with this electrical part.
MAX4752EUD+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4752EUD+T Applications
There are a lot of Maxim Integrated MAX4752EUD+T Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial
- Communication systems
- Mechanical reed relay replacement
- Transmit
- Digital Cross-Connects
- PDH Multiplexers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ATM
