banner_page

MAX4753EUD+T

30ns, 25ns SPST - NO/NC 900mOhm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4753 14 Pins 2.5nA 1.8V 14-TSSOP (0.173, 4.40mm Width)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4753EUD+T
  • Package: 14-TSSOP (0.173, 4.40mm Width)
  • Datasheet: PDF
  • Stock: 102
  • Description: 30ns, 25ns SPST - NO/NC 900mOhm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4753 14 Pins 2.5nA 1.8V 14-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-TSSOP (0.173, 4.40mm Width)
Number of Pins 14
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2012
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
Resistance 900mOhm
Terminal Finish MATTE TIN
Subcategory Multiplexer or Switches
Max Power Dissipation 727mW
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 1.8V
Terminal Pitch 0.65mm
Base Part Number MAX4753
Output SEPARATE OUTPUT
Pin Count 14
Operating Supply Voltage 3V
Number of Channels 1
Number of Circuits 4
Max Supply Voltage 3.6V
Min Supply Voltage 1.6V
Operating Supply Current 1μA
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 35 ns
Supply Type Single
Turn-Off Delay Time 25 ns
On-State Resistance (Max) 900mOhm
Multiplexer/Demultiplexer Circuit 1:1
Current - Leakage (IS(off)) (Max) 2.5nA
Channel Capacitance (CS(off), CD(off)) 31pF 30pF
On-state Resistance Match-Nom 0.05Ohm
Switch Circuit SPST - NO/NC
Switch Time (Ton, Toff) (Max) 30ns, 25ns
Charge Injection 21pC
Channel-to-Channel Matching (ΔRon) 30m Ω
Crosstalk -80dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.6V~3.6V
Height Seated (Max) 1.1mm
Length 5mm
Radiation Hardening No
RoHS Status ROHS3 Compliant

MAX4753EUD+T Overview


Presented in 14-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. A total of 14 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. A key feature of the 14 series is the inclusion of this electronic part as part of its design. A SPST - NO/NC switching circuit is used to build these analog multiplexers. This multiplexer is composed of 4 circuits. Look for analog switch ic variants by searching with MAX4753. Internally, this switch multiplexer has a resistance of 900mOhm. To find out what the 14 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.6V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 1μA. A voltage of 1.6V~3.6V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 3V.

MAX4753EUD+T Features


1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current

MAX4753EUD+T Applications


There are a lot of Maxim Integrated MAX4753EUD+T Analog Switches & Multiplexers ICs applications.

  • T1/E1 Terminals
  • Avionics test equipment
  • Fault Tolerant Systems
  • Microwave transmission systems
  • Routers
  • Mechanical reed relay replacement
  • Communications systems
  • SDH/SONET multiplexers
  • HDTV
  • PBXs

Write a review

Note: HTML is not translated!
    Bad           Good