MAX4754ETE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 850mOhm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.349W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4754 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 200nA |
| Nominal Supply Current | 12μA |
| Max Supply Current | 2μA |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 140 ns |
| -3db Bandwidth | 10MHz |
| On-State Resistance (Max) | 850mOhm |
| High Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 120 dB |
| Current - Leakage (IS(off)) (Max) | 4nA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 300pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 140ns, 50ns |
| Charge Injection | 300pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4754ETE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-WQFN Exposed Pad. To ensure high reliability, a new packaging method Tube is used. This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. The total number of terminations is 16. A 2 channel electronic part produces high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPDT switching circuits. This multiplexer is composed of 4 circuits. Using the MAX4754 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 850mOhm. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. 1.8V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 200nA current. Draining from a single voltage supply, this analog switch requires a voltage of 1.8V~5.5V. A voltage higher than 2μA may cause damage to the switch multiplexer. It can operate from 5V operating voltages.
MAX4754ETE+ Features
2 Channels
Switch Circuit: SPDT
200nA Supply Current
-3db Bandwidth: 10MHz
MAX4754ETE+ Applications
There are a lot of Maxim Integrated MAX4754ETE+ Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Medical Instrumentation
- Communication systems
- Channel Banks
- Industrial
- USB 1.1 signal switching circuits
- Switching Systems
- Communication systems
- Battery Powered Instruments
- Sample hold systems
