MAX4758EBX+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 36-WFBGA, CSPBGA |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 36 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4758 |
| Output | SEPARATE OUTPUT |
| Pin Count | 36 |
| JESD-30 Code | S-PBGA-B36 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 850mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 95 dB |
| Current - Leakage (IS(off)) (Max) | 4nA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 300pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 140ns, 50ns |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.67mm |
| Length | 3.06mm |
| RoHS Status | ROHS3 Compliant |
MAX4758EBX+T Overview
Shipping overseas is convenient with the electronic component packed in 36-WFBGA, CSPBGA. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. There is 2:2 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 36 terminations have occurred. As a result of its 2 channels, this electronic component provides high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 36 series is equipped with this electronic component. Based on DPDT switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 4. Use MAX4758 to search for variants of the digital switches. Theswitch device is a typical Multiplexer or Switches. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4758EBX+T Features
2 Channels
Switch Circuit: DPDT
-3db Bandwidth: 50MHz
MAX4758EBX+T Applications
There are a lot of Maxim Integrated MAX4758EBX+T Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Multi-Line E1 Interface Cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Microprocessor controlled systems
- Channelized and Unchannelized DS3 applications
- ATM
- PDAs
- Relay replacements
- Industrial
- Cable Telephony – NIU, Set-Top Box, Home Side Box
