MAX4758ETX+

140ns, 50ns DPDT 850mOhm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4758 36 Pins 4nA 3V 36-WFQFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4758ETX+
Package: 36-WFQFN Exposed Pad
Datasheet: PDF
Stock: 100
Description: 140ns, 50ns DPDT 850mOhm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4758 36 Pins 4nA 3V 36-WFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	36-WFQFN Exposed Pad
Number of Pins	36
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	36
ECCN Code	EAR99
Resistance	850mOhm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	2.1W
Technology	CMOS
Terminal Position	QUAD
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	3V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4758
Output	SEPARATE OUTPUT
Pin Count	36
Power Supplies	3/5V
Number of Channels	2
Number of Circuits	4
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	1μA
Nominal Supply Current	10nA
Max Supply Current	10nA
Turn On Delay Time	140 ns
Supply Type	Single
Turn-Off Delay Time	50 ns
-3db Bandwidth	50MHz
On-State Resistance (Max)	850mOhm
Multiplexer/Demultiplexer Circuit	2:2
Off-state Isolation-Nom	95 dB
Current - Leakage (IS(off)) (Max)	4nA
Channel Capacitance (CS(off), CD(off))	180pF 300pF
On-state Resistance Match-Nom	0.1Ohm
Switch Circuit	DPDT
Switch Time (Ton, Toff) (Max)	140ns, 50ns
Charge Injection	40pC
Channel-to-Channel Matching (ΔRon)	100m Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	1.8V~5.5V
Height Seated (Max)	0.8mm
Length	6mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4758ETX+ Overview

As the electronic part is packed in 36-WFQFN Exposed Pad, international shipping is convenient. High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 2:2. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 36 terminations. High-quality output is provided by the electronic component's 2 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. This electronic part can be found in the 36 series. Circuits based on DPDT switching are used to construct these analog switch ics. There are 4 circuits in this multiplexer. Try searching for the analog switch ic with MAX4758 if you are looking for variants. In this multiplexer, the internal resistance is 850mOhm. To find out what the 36 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. There should be 1.8V voltage fed to the electrical part below 1.8V. For this digital switch to work, 1μA current would suffice. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. Put voltage above 10nA on the multiplexer to cause damage. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.