MAX4758ETX+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-WFQFN Exposed Pad |
| Number of Pins | 36 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Resistance | 850mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.105W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4758 |
| Output | SEPARATE OUTPUT |
| Pin Count | 36 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 140 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 850mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 95 dB |
| Current - Leakage (IS(off)) (Max) | 4nA |
| Channel Capacitance (CS(off), CD(off)) | 180pF 300pF |
| On-state Resistance Match-Nom | 0.35Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 140ns, 50ns |
| Charge Injection | 40pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.8mm |
| Length | 6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4758ETX+T Overview
Shipping overseas is convenient with the electronic component packed in 36-WFQFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:2. The operating temperature is extended to around -40°C~85°C TA. In total, there are 36 terminations. A high-quality output is provided by the electrical component's 4 channels. An 3V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 36 pins. Based on DPDT switching circuits, these analog multiplexers work. Circuits number 4 make up this analogue multiplexer. Try searching with MAX4758 if you're looking for variants. It has an internal resistance of 850mOhm. The functions of 36 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.8V. For this multiplexer to operate, 1μA current would be sufficient. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 5V operating voltages are supported by the electronic component.
MAX4758ETX+T Features
4 Channels
Switch Circuit: DPDT
1μA Supply Current
-3db Bandwidth: 50MHz
MAX4758ETX+T Applications
There are a lot of Maxim Integrated MAX4758ETX+T Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Audio and video switching
- HDTV
- Sample hold systems
- Cable Modem
- Battery Powered Systems
- Avionics
- Cell phones
- Avionics and Military Systems
- FTTH
