banner_page

MAX4760ETX-T

140ns, 50ns DPDT 3.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE 36 Pins 5nA 3V 36-WFQFN Exposed Pad


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX4760ETX-T
  • Package: 36-WFQFN Exposed Pad
  • Datasheet: -
  • Stock: 745
  • Description: 140ns, 50ns DPDT 3.5Ohm QUAD Analog Switches BREAK-BEFORE-MAKE 36 Pins 5nA 3V 36-WFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Package / Case 36-WFQFN Exposed Pad
Number of Pins 36
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 36
ECCN Code EAR99
Resistance 3.5Ohm
Subcategory Multiplexer or Switches
Max Power Dissipation 2.105W
Technology CMOS
Terminal Position QUAD
Number of Functions 4
Supply Voltage 3V
Terminal Pitch 0.5mm
Pin Count 36
Operating Supply Voltage 5V
Polarity Non-Inverting
Number of Channels 2
Number of Circuits 4
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 10nA
Nominal Supply Current 12μA
Max Supply Current 1μA
Turn On Delay Time 800 ns
Supply Type Single
Turn-Off Delay Time 800 ns
-3db Bandwidth 150MHz
On-State Resistance (Max) 3.5Ohm
High Level Output Current 100mA
Multiplexer/Demultiplexer Circuit 2:2
Off-state Isolation-Nom 100 dB
Current - Leakage (IS(off)) (Max) 5nA
Channel Capacitance (CS(off), CD(off)) 25pF
On-state Resistance Match-Nom 0.2Ohm
Switch Circuit DPDT
Switch Time (Ton, Toff) (Max) 140ns, 50ns
Charge Injection 15pC
Channel-to-Channel Matching (ΔRon) 200m Ω
Crosstalk -95dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-off Time-Max 50ns
Voltage - Supply, Single (V+) 1.8V~5.5V
Height Seated (Max) 0.8mm
Length 6mm
Radiation Hardening No
RoHS Status RoHS Compliant
Contact Plating Tin
Mount Surface Mount
Mounting Type Surface Mount

MAX4760ETX-T Overview


The electrical component comes in 36-WFQFN Exposed Pad packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. There are 36 terminations totally. This electronic part offers high-quality output due to its 2 channels. With a 3V voltage supply, the electrical component should be turned on and run. An electrical component like this is included in the 36 series. A DPDT switching circuit is used to build these analog multiplexers. 4 circuits are used in this analogue multiplexer. In this multiplexer, the internal resistance is 3.5Ohm. To find out what the functions of 36 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 1.8V. It would be sufficient to run this analogue multiplexer with 10nA current. This analogue multiplexer requires a voltage of 1.8V~5.5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. Operating voltages range from 5V.

MAX4760ETX-T Features


2 Channels
Switch Circuit: DPDT
10nA Supply Current
-3db Bandwidth: 150MHz

MAX4760ETX-T Applications


There are a lot of Maxim Integrated MAX4760ETX-T Analog Switches & Multiplexers ICs applications.

  • Cellular phones
  • Relay Replacement
  • High reliability control systems
  • Automotive applications
  • Optical Applications
  • Data Acquisition Systems
  • Cell phones
  • Residential Gateways, Home Gateway/Router
  • USB 1.1 signal switching circuits
  • PDAs

Write a review

Note: HTML is not translated!
    Bad           Good