MAX4760EWX+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-WFBGA, WLBGA |
| Number of Pins | 36 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Resistance | 3.5Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.105W |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4760 |
| Output | SEPARATE OUTPUT |
| Pin Count | 36 |
| Power Supplies | 3/5V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 12μA |
| Turn On Delay Time | 800 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 800 ns |
| -3db Bandwidth | 150MHz |
| On-State Resistance (Max) | 3.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 140ns, 50ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 0.67mm |
| Length | 3.06mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4760EWX+T Overview
Shipping overseas is convenient due to the electrical component's packing in 36-WFBGA, WLBGA. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. There is 2:2 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 36. A high-quality output is provided by the electrical component's 2 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. There is an electrical component included in the 36 series. Based on DPDT switching circuits, these analog multiplexers work. A 4 circuit is present in this switch device. Try searching for the analog switch ic with MAX4760 if you are looking for variants. Internally, this switch multiplexer has a resistance of 3.5Ohm. Please refer to the datasheets for 36 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.8V. It would be sufficient to run this analogue multiplexer with 10nA current. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4760EWX+T Features
2 Channels
Switch Circuit: DPDT
10nA Supply Current
-3db Bandwidth: 150MHz
MAX4760EWX+T Applications
There are a lot of Maxim Integrated MAX4760EWX+T Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- RGB switches
- Optical Applications
- Data switching
- Fault Tolerant Systems
- MP3 players
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample hold systems
- Remote wireless modules
