Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
36-WFQFN Exposed Pad |
Number of Pins |
36 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
36 |
ECCN Code |
EAR99 |
Resistance |
3.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
2.105W |
Technology |
CMOS |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4761 |
Output |
SEPARATE OUTPUT |
Pin Count |
36 |
Operating Supply Voltage |
5V |
Number of Channels |
4 |
Number of Circuits |
8 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Analog IC - Other Type |
DPDT |
Operating Supply Current |
1μA |
Nominal Supply Current |
12μA |
Max Supply Current |
1μA |
Turn On Delay Time |
50 ns |
Supply Type |
Single |
Turn-Off Delay Time |
140 ns |
-3db Bandwidth |
150MHz |
On-State Resistance (Max) |
3.5Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
100 dB |
Current - Leakage (IS(off)) (Max) |
5nA |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.2Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
140ns, 50ns |
Charge Injection |
15pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Length |
6mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX4761ETX+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 36-WFQFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. There are 36 terminations totally. A high-quality output is provided by the electrical component's 4 channels. An 3V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 36 series. Circuits based on SPDT switching are used to construct these analog switch ics. Circuits number 8 make up this analogue multiplexer. Try searching for the analog switch ic with MAX4761 if you are looking for variants. It has an internal resistance of 3.5Ohm. Datasheets for 36 pin functions are available upon request. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. This multiplexer would work with 1μA current. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. Putting voltage greater than 1μA on the multiplexer may cause damage. A DPDT analog IC is integrated into the board. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages range from 5V.
MAX4761ETX+ Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 150MHz
MAX4761ETX+ Applications
There are a lot of Maxim Integrated MAX4761ETX+ Analog Switches & Multiplexers ICs applications.
- Communication systems
- Precision data acquisition
- Access Concentrators
- Data Acquisition Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- T1/E1 Terminals
- Ultrasound
- Channelized and Unchannelized DS3 applications
- Digital cross connects (DSX-1)
- PCMCIA cards