MAX4761ETX+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-WFQFN Exposed Pad |
| Number of Pins | 36 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Resistance | 3.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 2.105W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4761 |
| Pin Count | 36 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Analog IC - Other Type | DPDT |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 12μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 50 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 140 ns |
| -3db Bandwidth | 150MHz |
| On-State Resistance (Max) | 3.5Ohm |
| High Level Output Current | 100mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 140ns, 50ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Length | 6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4761ETX+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 36-WFQFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 36 terminations. A 2 channel electronic part produces high-quality output. A 3V voltage supply should turn on and run the electronic component. Electronic part bodies are injected with 36 pins. Circuits based on SPDT switching are used to construct these analog switch ics. A total of 8 circuits make up this switch device. Try searching with MAX4761 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 3.5Ohm. For functions related to 36 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 5.5V in normal situations. The digital multiplexer has a low cost Single supply. The lowest voltage the electronic part should receive is 1.8V. This digital switch can be operated with a current of 1μA. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. It is integrated with a DPDT analog IC. 5V operating voltages can be used with this electrical part.
MAX4761ETX+T Features
2 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 150MHz
MAX4761ETX+T Applications
There are a lot of Maxim Integrated MAX4761ETX+T Analog Switches & Multiplexers ICs applications.
- RGB switches
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- SONET
- Frame Relay Equipment
- Mechanical reed relay replacement
- Video switching
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Channelized and Unchannelized DS3 applications
- Precision instrumentation
- Avionics
