Parameters |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.6V~3.6V |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
1Ohm |
Max Power Dissipation |
457mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4781 |
Pin Count |
16 |
Operating Supply Voltage |
3V |
Number of Channels |
8 |
Number of Circuits |
1 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.6V |
Operating Supply Current |
1μA |
Propagation Delay |
25 ns |
Turn On Delay Time |
30 ns |
Logic Function |
Multiplexer |
Supply Type |
Single |
Turn-Off Delay Time |
20 ns |
On-State Resistance (Max) |
1Ohm |
High Level Output Current |
150mA |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
38pF 310pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Time (Ton, Toff) (Max) |
25ns, 15ns |
Charge Injection |
-110pC |
MAX4781EUE+T Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 8:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. As a result of its 8 channels, this electronic component provides high-quality output. A 1.8V voltage supply should turn on and run the electronic component. Into the electrical component body are injected 16 pins. Circuits number 1 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4781. It has an internal resistance of 1Ohm. For functions related to 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 3.6V. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 1.6V. For this multiplexer to operate, 1μA current would be sufficient. This analogue multiplexer requires a voltage of 1.6V~3.6V when it drains from a single voltage supply. The electronic component can function from 3V.
MAX4781EUE+T Features
8 Channels
1μA Supply Current
MAX4781EUE+T Applications
There are a lot of Maxim Integrated MAX4781EUE+T Analog Switches & Multiplexers ICs applications.
- PDAs
- Digital Cross-Connects
- Medical systems
- Sample-and-hold systems
- T1/E1 Terminals
- Voice over IP/DSL – Integrated Access Devices, Smart
- High speed data transmission line cards
- Audio and video switching
- HDTV
- Mechanical reed relay replacement