MAX4782ETE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 1.349W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4782 |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Propagation Delay | 25 ns |
| Turn On Delay Time | 30 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.001mA |
| Turn-Off Delay Time | 20 ns |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 38pF 158pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 25ns, 15ns |
| Charge Injection | -110pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 1.6V~3.6V |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 0.8mm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4782ETE+T Overview
The electrical component comes in 16-WFQFN Exposed Pad packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. A 4 channel electronic part produces high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. A SP4T switching circuit is used for these analog switches. Circuits number 2 make up this analogue multiplexer. Use MAX4782 to search for variants of the digital switches. Analog switches have 1Ohm internal resistance. Please refer to the datasheets for 16 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 3.6V. The digital multiplexer has a low cost Single supply. There should be 1.6V voltage fed to the electrical part below 1.6V. This digital switch can be operated with a current of 1μA. Draining from a single voltage supply, this analog switch requires a voltage of 1.6V~3.6V. 3V operating voltages are supported by the electronic component.
MAX4782ETE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4782ETE+T Applications
There are a lot of Maxim Integrated MAX4782ETE+T Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Signal routing between systems
- Transmit
- Relay replacements
- Channel Banks
- PBXs
- Data Acquisition Systems
- Audio and video switching
- Wireless Local Loop
- E1 Multiplexer
