MAX4800CXZ-T
| Parameters | |
|---|---|
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 26-LFBGA, CSPBGA |
| Number of Pins | 26 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 26 |
| ECCN Code | EAR99 |
| Resistance | 48Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 941mW |
| Technology | BCDMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 26 |
| Power Supplies | 3/13V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Nominal Supply Current | 2mA |
| Max Supply Current | 4mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5 μs |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 5 μs |
| Max Dual Supply Voltage | 185V |
| On-State Resistance (Max) | 38Ohm |
| Min Dual Supply Voltage | 40V |
| Dual Supply Voltage | 100V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 77 dB |
| Current - Leakage (IS(off)) (Max) | 4μA |
| Channel Capacitance (CS(off), CD(off)) | 18pF |
| On-state Resistance Match-Nom | 1.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5μs, 5μs |
| Charge Injection | 820pC |
| Channel-to-Channel Matching (ΔRon) | 1.9 Ω |
| Crosstalk | -80dB @ 5MHz |
| Switch-on Time-Max | 5000ns |
| Switch-off Time-Max | 5000ns |
| Voltage - Supply, Single (V+) | 2.7V~13.2V |
| Normal Position | NO |
| Height Seated (Max) | 1.32mm |
| Length | 6mm |
| Width | 5.35mm |
MAX4800CXZ-T Overview
As the electronic part is packed in 26-LFBGA, CSPBGA, international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around 0°C~70°C. In total, 26 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. It is part of the design of the 26 series that this electronic component is included. SPST - NO switching circuits are used in these analog switch ics. The multiplexer consists of 8 circuits. In this multiplexer, the internal resistance is 48Ohm. For functions related to 26 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. Draining from a single voltage supply, this analog switch requires a voltage of 2.7V~13.2V. Put voltage above 4mA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 185V. The voltage should be at least 40V if you are using dual power supplies.
MAX4800CXZ-T Features
1 Channels
Switch Circuit: SPST - NO
MAX4800CXZ-T Applications
There are a lot of Maxim Integrated MAX4800CXZ-T Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- PDH Multiplexers
- Sample hold systems
- Isolation
- Battery-powered systems
- T1/E1 Terminals
- PCMCIA cards
- Power routing
- Industrial
- DSLAMs
