MAX4802ACCM+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 48-LQFP |
| Number of Pins | 48 |
| Weight | 181.692094mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tray |
| Published | 2008 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 48 |
| ECCN Code | EAR99 |
| Resistance | 25Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.818W |
| Technology | BCDMOS |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4802 |
| Output | SEPARATE OUTPUT |
| Pin Count | 48 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2.7V |
| Max Supply Current | 3μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5 μs |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 5 μs |
| Max Dual Supply Voltage | 185V |
| On-State Resistance (Max) | 38Ohm |
| Min Dual Supply Voltage | 40V |
| Dual Supply Voltage | 100V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 33 dB |
| Current - Leakage (IS(off)) (Max) | 2μA |
| Channel Capacitance (CS(off), CD(off)) | 18pF |
| On-state Resistance Match-Nom | 1.9Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5μs, 5μs |
| Channel-to-Channel Matching (ΔRon) | 1.9 Ω |
| Crosstalk | -80dB @ 5MHz |
| Switch-on Time-Max | 5000ns |
| Switch-off Time-Max | 5000ns |
| Voltage - Supply, Single (V+) | 2.7V~6V |
| Normal Position | NO |
| Height Seated (Max) | 1.6mm |
| Length | 7mm |
| Width | 7mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
MAX4802ACCM+ Overview
As the electronic part is packed in 48-LQFP, international shipping is convenient. High reliability is achieved by using advanced packaging method Tray. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. The total number of terminations is 48. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. A total of 48 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO switching circuits. A 8 circuit is present in this switch device. Try searching with MAX4802 to find analog multiplexer variants. This digital multiplexer has 25Ohm internal resistance. To find out what the functions of 48 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 6V in normal situations. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 2.7V as the lowest voltage for the electrical part. Using a single voltage supply, this switch device consumes 2.7V~6V volts. Putting voltage greater than 3μA on the multiplexer may cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 185V. You should attach at least 40V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4802ACCM+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4802ACCM+ Applications
There are a lot of Maxim Integrated MAX4802ACCM+ Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Avionics test equipment
- Precision instrumentation
- PBX interfaces
- 65 V DACs
- Fiber to the Home
- E1 Network Equipment
- ATM
- Cable PC
- Relay Replacement
